Beginner's Plumbing: What You Need for Bathtub Installation
Beginner's Plumbing: What You Need for Bathtub Installation
Blog Article
How do you feel in regards to How to Install a Bathtub Yourself?
Installing a tub isn't specifically brain surgery, yet it does need solid plumbing, woodworking, and occasionally, tiling skills. Changing an old bath tub with a brand-new one is likewise a moderately difficult task. If the old bathtub is readily easily accessible, the task can move speedily; if you have to open up a wall to eliminate the old bathtub as well as place the brand-new bath tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will require an assistant to move out the old tub and set in the brand-new one. Make sure you have actually certified on your own for the job and are comfortable attempting it. As opposed to working with a service provider to take control of a halfway-completed project, it is much better to consider utilizing one prior to you begin. Opportunities are you might require a professional plumber to make tube connections.
This write-up will aid you set up a new tub in your bathroom if you have currently acquired a new tub as well as don't require to transform the arrangement of your previous supply of water pipelines.
Your tools and material list ought to make up the following:
Getting ready for the Installment
First of all, the sustaining structure supplied with the bath must be fitted (if required) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bathtub. When suitable the faucet block, it is necessary to make certain that if the faucet features a plastic washing machine, it is fitted in between the bathroom as well as the taps. On a plastic bathroom, it is likewise practical to fit a supporting plate under the faucets system to avoid strain on the tub.
Fit the flexible faucet connectors to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the outlet with the hole in the bath. Use the nut supplied by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bathroom. Make sure you make use of all of the provided washers.
Attach the trap to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a comparable manner.The bathroom need to currently be ready to be fitted in its final position.
Removing Old Touches
If you need to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is disconnect the water supply. After doing so, activate the taps to drain any water continuing to be in the system. The procedure of eliminating the existing taps can be quite bothersome because of the limited gain access to that is typically the situation.
Make use of a container wrench (crowsfoot spanner) or a tap tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. Once the supply pipes have been removed, utilize the very same tool to loosen up the nut that holds the faucets onto the bath/basin. You will require to stop the single faucets from transforming during this procedure. When the faucets have been eliminated, the holes in the bath/basin will need to be cleansed of any old securing substance.
Before going on to fit the new taps, contrast the pipe connections on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new faucets to fit.
Mounting the Bath tub
Utilizing both wood boards under its feet, position the bath tub in the needed setting. The wooden boards are practical in equally spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto four small points.
The following goal is to make sure that the bathtub is leveled all round. This can be accomplished by inspecting the level and readjusting the feet on the bath tub until the spirit level reads level.
To mount faucets, fit the bottom of the outermost flexible faucet port to the appropriate supply pipeline by making a compression join; after that do the same for the other faucet.
Turn on the water and also check all joints and new pipework for leaks and tighten them if necessary. Fill up the bathtub as well as additionally examine the overflow electrical outlet and also the normal electrical outlet for leaks.
Ultimately, fix the bath paneling as defined in the producer's user's manual. Tiling and securing around the bath tub should wait up until the bath tub has been used at the very least when as this will certainly settle it right into its final position.
Suitable New Taps
If the tails of the new faucets are plastic, after that you will require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the tap as well as the various other end provides a connection to the existent supply pipes.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the basic 15mm supply pipe.
Next, place the tap in the installing opening in the bath/basin making sure that the washers are in place in between the tap as well as the sink. Protect the faucet in place with the manufacturer provided backnut. When the tap is securely in place, the supply pipelines can be attached to the tails of the faucets. The faucets can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind must be attached to the tap finishes initially, tightening up just by hand. The supply pipelines can later on be attached to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bathroom satisfies the tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture an inflexible seal, triggering the water to penetrate the wall in between the bathroom and the tiling, bring about difficulties with moisture and also possible leaks to the ceiling listed below.
You can choose from a selection of coloured sealants to blend in your components and also fittings. They are marketed in tubes and cartridges, as well as can securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the bath tub with water before sealing, to permit the activity experienced when the tub is in use. The sealant can fracture fairly very early if you do not consider this motion before securing.
Additionally, ceramic coving or quadrant floor tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly available on the market. It is advisable to fit the ceramic tiles utilizing water-resistant or water resistant sticky as well as grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I was brought to that article on How to Install a Bathtub through an acquaintance on another web property. Loved our review? Please share it. Help another person check it out. We appreciate reading our article about How to Install a Bathtub.
Or Book Technician Here Report this page